VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
+ 2. VR6 engine
+ 3. Two-liter engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
+ 13. Forward suspension bracket
+ 14. Back suspension bracket
- 15. Brake system
   + 15.1. Adjustment of brake system
   + 15.2. Disk brakes of forward wheels
   + 15.3. Brakes of back wheels
   15.4. Processing of brake disks
   + 15.5. Main brake cylinder
   15.6. Check of the vacuum amplifier of a brake drive
   15.7. Pumping of brakes
   - 15.8. Parking brake
      15.8.1. Removal and installation of a cable of a drive of the parking brake
      15.8.2. Removal and installation of the lever of a drive of the parking brake
   + 15.9. ABS system (anti-blocking brake system)
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema


Repair Sharan/Sharan Volkswagen>> Brake system>> Parking brake>> Removal and installation of a cable of a drive of the parking brake
Removal of hummock draft of the lever of a drive of the parking brake carry out in the following order:
- weaken bolts of fastening of back wheels, put a back part of the car on a support and remove wheels;
- establish the lever of a drive of the parking brake in extreme bottom situation;
Fig. 330. Details of lay brake system: 1 — the handle; 2 — a casing of the lever of the parking brake; 3 — a lever frame; 4 — a bolt, 25 N · m; 5 — a sharnirny bolt; 6 — the lever of a drive of the parking brake; 7 — the contact switch; 8 — a protective cover of hummock draft of the lever of the parking brake; 9 — шплинт; 10 — hummock draft of the lever of the parking brake; 11 — the equalizer; 12 — an adjusting nut; 13 — spring fastening; 14 — a returnable spring; 15 — a fastening loop.





- turn on an adjusting nut 12 (fig. 330) of a cable of the 10th drive of the parking brake until rychazhka of a manual drive on back brake supports will not depart to the emphasis;
- remove weakened cables of a drive of the parking brake from the equalizer 11 and from fastening brackets;
Fig. 331. Places of fastening of cables of a drive of the parking brake on a back suspension bracket (are shown by shooters)





- disconnect from fastenings on a back suspension bracket (fig. 331) cables of a drive of the parking brake;
- disconnect cables of a drive of the parking brake from rychazhok of a manual drive on back brake supports. For this purpose take out a lock collar, pull a cable against a tension of a spring and unhook the cable end from a rychazhka;
- take out a cable through a back suspension bracket.
Check a condition of details of lay brake system. If break, a peretiraniye a cable provolok, bad fastening of tips on it are found or cover damage, a cable replace new. Teeths of sector and a latch should not have damages. And the lever should be fixed reliably in a standard position and it is easy to move up-down. The damaged and worn-out details replace.
Installation of hummock draft of the lever of a drive of the parking brake carry out as it should be, the return to removal. After installation adjust the parking brake and tighten bolts of fastening of back wheels the moment of 140 N · m.