VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
+ 2. VR6 engine
+ 3. Two-liter engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
- 13. Forward suspension bracket
   13.1. Removal and installation
   + 13.2. Repair of a forward suspension bracket
   13.3. Stabilizer of cross-section stability
   + 13.4. Adjustment of corners of installation of forward wheels
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema








Repair Sharan/Sharan Volkswagen>> Forward suspension bracket>> Stabilizer of cross-section stability
The way of fastening of the stabilizer of cross-section stability is shown in drawing 291 . To get access to the stabilizer of cross-section stability remove a stretcher and a pendular support:
- establish a forward part of the car on support;
- remove protection of the engine;
- from salon separate connection of a steering column and the steering mechanism (see item 12.1);
- remove connecting draft of the stabilizer of cross-section stability;

Fig. 293. Fastening of 1 stabilizer of cross-section stability to a stretcher





- remove fastening of 1 stabilizer of cross-section stability from a stretcher (fig. 293) ;
- establish a jack under a stretcher;

Fig. 294. Removal of a pendular support from a transmission: 1 — a bolt; 2 — a washer; 3 rubber support; 4 — a pendular support





- remove a pendular support of a transmission (fig. 294) . Unscrew a bolt 1 and remove it together with a washer 2. Remove a rubber support 3 and wring out a pendular support 4;

Fig. 295. On each party of the car are located on two bolts of fastening of a stretcher (are shown by shooters)





- unscrew four bolts of fastening of a stretcher. Unscrew two bolts (fig. 295) from each party of the car;
- slowly lower a stretcher and remove the stabilizer of cross-section stability.
Installation is carried out in return sequence concerning removal process, thus:
- do not damage a sheeting of the stabilizer of cross-section stability;
- do not damage protective covers of hinges;

Fig. 291. Fastening of the cross-section lever, the stabilizer of cross-section stability and a pendular support on a stretcher: 1 — a stretcher; 2 — a nut, 55 N · m; 3 — a rubber support; 4 — самоконтрящаяся a nut, 100 N · m (replace always); 5 — a fixing bracket; 6 — a bolt; 7 — connecting draft; 8 — the stabilizer of cross-section stability; 9 — самоконтрящаяся a nut, 100 N · m (replace always); 10 — M14x1,5 bolt, length of 65 mm, 150 N · m + 90 °; 11 — the back bearing of the cross-section lever; 12 — M14x1,5 bolt, length of 95 mm, 150 N · m + 90 ° (replace always); 13 — a spherical support; 14 — a bolt, 55 N · m; 15 — самоконтрящаяся a nut, 55 N · m (replace always); 16 — the cross-section lever; 17 — the bearing of the cross-section lever; 18 — a bolt, 90 N · m + 90 °; 19 — a bolt, 100 N · m; 20 — a rubber support; 21 — a pendular support; 22 — a nut, 100 N · m; 23 — a bolt





- replace 291 bolts specified fig. and nuts;
- the moments of an inhaling of carving connections are specified at the end of the book.