VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
+ 2. VR6 engine
+ 3. Two-liter engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
+ 13. Forward suspension bracket
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
- Specifications and characteristics
   + Appendix 1. Specifications and characteristics
   + Appendix 2. A specification for adjustments and control
   - Appendix 3. Moments of an inhaling of carving connections
      VR6 engine
      Engine of 2,0 L
      Diesel engine
      Back suspension bracket (see fig. 300)
      Brake system
+ Elektroskhema




Repair Sharan/Sharan Volkswagen>> Specifications and characteristics>> Appendix 3. Moments of an inhaling of carving connections>> Diesel engine
Bolts of fastening of a head of the block of cylinders:        
 first pass       of 40 N · m
 second pass       of 60 N · m
 the third pass       Tighten on a turn quarter
 the fourth pass       Tighten on a turn quarter
 the fifth pass       Warm up the engine and tighten bolts without a dinamometrichesky key on a turn quarter (90 °), without weakening them before it
Cover of the radical bearing       of 65 N · m, +90 °
Cover of the bearing of a rod:       
 first pass       of 30 N · m
 the second pass       Tighten on 90 ° Grease basic surfaces of nuts
Bolts of a flywheel       of 60 N · m, +90 °
Cogwheel of an intermediate shaft       of 45 N · m
Cogwheel of a cranked shaft:       
 first pass       of 90 N · m
 second pass       +90 °
Pulley of a cranked shaft on a quencher of fluctuations       of 25 N · m
Protection of a gear driving belt on the block of cylinders       of 10 N · m
Nut of the tension adaptation of a gear driving belt       of 20 N · m
Arm of the bearing of the fuel pump of a high pressure       of 25 N · m
The fuel pump of a high pressure on an arm of the bearing        of 25 N · m
Cogwheel of the fuel pump of a high pressure        of 55 N · m
Cover of a head of the block of cylinders        of 10 N · m
The water pump on the engine        of 20 N · m
The oil pump on the engine:       
 short bolts       of 10 N · m
 long bolts        of 20 N · m
Oil case to the block of cylinders        of 20 N · m
Maslopriyemny pipe to a cover
oil pump       of 10 N · m
Internal protection of a driving belt       of 30 N · m
Basis of the oil filter       of 20 N · m
Oil radiator to the basis of the filter       of 25 N · m
Stopper of a drain opening       of 30 N · m
Exhaust pipe on a head of the block of cylinders       of 25 N · m
Exhaust pipe on an inlet collector       of 25 N · m
Clamping plate of the vacuum pump       of 25 N · m
Stretcher       of 150 N · m, +90 °
Plate of the spherical hinge to a rotary fist       of 55 N · m
Nut of the bearing spherical hinge       of 30 N · m, + 90 °
Bolt, amortizatornay rack on a rotary fist       of 110 N · m
Assembly framework of a bracket of the disk brake mechanism of a wheel       of 200 N · m
Bracket of the disk brake mechanism to an assembly frame       of 25 N · m
Bolt, sensor of frequency of rotation       of 4 N · m
Bolt of a power shaft       of 150 N · m, + 90 °
Amortization rack of the chassis to a body       of 60 N · m
Reflector on a rotary fist       of 10 N · m
Power shafts to a transmission       of 45 N · m
The top bearing of an amortization rack of the chassis to a rod of the piston       of 60 N · m
Bolt of a brake disk       of 10 N · m