VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
- 2. VR6 engine
   + 2.1. Cнятие and installation
   + 2.2. Dismantling and assembly
   + 2.3. Head of the block of cylinders and valves
   + 2.4. Pistons and rods
   2.5. Block of cylinders
   + 2.6. Cranked shaft and radical bearings
   + 2.7. Drive of the mechanism of a gazoraspredeleniye
   2.8. Intermediate shaft
   2.9. Compression check in engine cylinders
   + 2.10. System of production of the fulfilled gases
+ 3. Two-liter engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
+ 13. Forward suspension bracket
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema




Repair Sharan/Sharan Volkswagen>> VR6 engine>> Intermediate shaft

Fig. 69. The block of cylinders with the details established on it: 1 — a bolt, 25 N · m; 2 — a pulley of the pump of cooling; 3 — a bolt, 20 N · m; 4 — the pump of system of cooling; 5 — an O-shaped sealing ring, always replace new; 6 — maslomerny щуп with a directing tube; 7 — blocking of removal of oil, 5 N · m; 8 — the detonation No. 2 sensor (for correction of the moment of ignition); 9 — the screw, 5 N · m; 10 — a cover of a drive of the oil pump; 11 — an O-shaped sealing ring, always replace new; 12 — a drive of the oil pump; 13 — the block of cylinders; 14 — an intermediate shaft; 15 — the adjusting washer, an inscription on it should look up; 16 — a bolt, 10 N · m; 17 — an O-shaped sealing ring, always replace new; 18 — laying of an oil case; 19 — the thermostat case; 20 — a bolt, 10 N · m; 21 — an O-shaped sealing ring, always replace new; 22 — the sensor of frequency of rotation of a cranked shaft; 23 — a bolt, 5 N · m; 24 — a bolt, 20 N · m; 25 — an O-shaped sealing ring





For removal of an intermediate shaft it is necessary to dismantle the engine from the car. To remove an intermediate shaft, it is necessary to remove a drive 12 (see fig. 69 ) the oil pump as the pump is put in action by intermediate shaft.

Fig. 91. Elements of a drive of the mechanism of a gazoraspredeleniye: 1 — an intermediate shaft; 2 — a leading ring; 3 — a bolt, 10 N · m; 4 — a sensor drive; 5 — a bolt, 10 N · m; 6 — a bolt, 25 N · m; 7 — an elastic element of the tension device; 8 — the tension device of a dvukhryadny chain, 20 N · m; 9 — a dvukhryadny chain; 10 — an asterisk of a drive of a dvukhryadny chain; 11 — an asterisk of a drive of a single-row chain; 12 — the tension device of a chain with a boot; 13 — an asterisk of a drive of the chain, built in a cranked shaft; 14 — a single-row chain; 15 — a level of an uspokoitel; 16 — a special bolt, 25 N · m; 17 — a finger from burty, 25 N · m; 18 — an uspokoitel; 19 — a bolt, 20 N · m; 20 — asterisks of cranked shaft





After removal of parts of a drive of the mechanism of a gazoraspredeleniye (see fig. 91 ) an intermediate shaft becomes easily available, it is possible to unscrew bolts of its fastening and a shaft to take.
Installation of the oil pump is carried out in sequence, return dismantling. Thus it is necessary to track, that on a directing ring of a shaft there was an adjusting label. The ring should be fastened so that the adjusting label was in the top part, differently it will not be possible to adjust a drive of the mechanism of a gazoraspredeleniye properly.