Fig. 352. Details of a back lamp: 1 — rubber sealing laying; 2 — the filament lamp of the index of turn, 21 In; 3 — the boss of filament lamps; 4 — the filament lamp of tail dimensional light, 21 In; 5 — a dvukhnitevy lamp of a stoplight and tail dimensional light, 21/5 W; 6 — a nut, 6 N · m; 7 — a rasseivatel of a lamp

In the case of back lamps from the right and left side of the car there are filament lamps of tail dimensional light 4 (fig. 352) , stoplights 5 and indexes of turn 2.

Other additional lamps are on a back door on the average the block of lighting devices.

Replacement of filament lamps of back lamps

Replacement of filament lamps of back lamps carry out in the following order:

- by means of a screw-driver remove clip-on earrings of an internal upholstery of a luggage carrier (in a salon corner, on the right or to the left of a luggage carrier);

- remove an internal upholstery of a luggage carrier in the corresponding corner of salon;

Fig. 353. Back lamp from the inside: 1 — the lock; 2 — a fastening nut

- by means of a screw-driver translate the lock 1 (fig. 353) so that it was possible to pull out a payment assembled;

- press a faulty lamp and, having turned counter-clockwise, take from the boss;

- insert into a cartridge a new lamp (holding a napkin) and turn clockwise before fixing.

Fig. 354. Removal of the case of a back lamp

If it is required to remove all case of a back lamp, unscrew from within bodies a key «on 8 mm» three nuts ( fig. 354 , it is shown by an arrow) fastenings of a back lamp. Outside of a body remove a back lamp and its rubber sealant. If porous, it it is necessary to replace a sealant in order to avoid moisture hit in the car.

Average block of back lighting devices

Fig. 355. Average block of back lighting devices: 1 — a lamp of a lamp of a backing; 2 — the boss of a lamp; 3 — a lamp of a back antifog lamp; 4 — a lamp of a lamp of a backing; 5 — the boss of a lamp; 6 — rubber sealing laying; 7 — glass of group of lighting devices; 8 — a lamp of illumination of registration plate; 9 — a lamp of a lamp of illumination of registration plate; 10 — a rasseivatel of a lamp of illumination of registration plate; 11 — the screw

The block of lighting devices located on a door of a luggage carrier of the Sharan car includes filament lamps of lamps of a backing 1 both 4 (fig. 355) and lamps of 3 back antifog lamps.

Removal of the block of lighting devices is made in the following order:

- open a luggage carrier door, turn out nine screws of fastening of an upholstery of a door and remove an upholstery down;

- disconnect electric sockets from both payments with lamps on the right and at the left, having hooked them a screw-driver;

Fig. 356. Places of fastening of the average block of lighting devices (are shown by shooters)

- unscrew nine nuts (fig. 356) of fastening of the block of lighting devices to a luggage carrier door;

- close a door of a luggage carrier and remove the block of lighting devices together with rubber sealing laying in the direction on itself.

Installation of the block of lighting devices is made as it should be, the return to removal, taking into account the following:

- tighten nine nuts of fastening of the block evenly around the moment of 6 N · m;

- pull from below an internal upholstery of a door of a luggage carrier so that openings coincided and tighten screws around;

- the porous or damaged rubber sealing laying replace on new in order to avoid moisture hit in the car.

Replacement of lamps of illumination of registration plate

Replacement of a lamp of illumination of registration plate carry out in the following order:

- turn out two screws 11 (see fig. 355 ) fastenings of a rasseivatel of the 10th lamp of illumination of registration plate;

- remove a rasseivatel;

- take a lamp with a glass socle and establish a new lamp;

- establish a rasseivatel.

Note After replacement of any lamp always check work of headlights and lamps, having included them.