VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
+ 2. VR6 engine
+ 3. Two-liter engine (ADY)
- 4. System of greasing of the engine
   4.1. Removal and installation of the pallet of a case
   + 4.2. Oil pump
   4.3. Oil filter
   4.4. Check of pressure of oil
   4.5. Oil radiator
   4.6. Oil replacement in the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
+ 13. Forward suspension bracket
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema




Repair Sharan/Sharan Volkswagen>> System of greasing of the engine>> Oil radiator
At operation of the engine the temperature of karterny oil should not raise strongly in order to avoid falling of its viscosity. Partial cooling of oil occurs in the pallet of a case and in the filter case owing to обдува their air from the fan of system of cooling. To more intensive cooling of karterny oil apply oil radiators.
Because of the different device of oil filters on VR6 engines and 2,0 l are used various oil radiators.
Engine of 2,0 l

Fig. 177. Details of the oil pump of the 2,0-liter engine: 1 — a bolt, 25 N · m; 2 — the basis of the oil filter; 3 — a sealing ring; 4 — an oil radiator; 5 — a nut, 25 N · m; 6 — the oil filter





On the 2,0-liter engine an oil radiator 4 (fig. 177) is located between the basis 2 oil filters and the oil filter 6. The oil radiator acts in film only after removal of the oil filter and a detachment of hoses. For this purpose unscrew a nut 5 from the bottom surface of an oil radiator. Between an oil radiator and the basis the sealing ring 3 is established. At assembly a nut it is necessary to tighten the moment of 25 N · m.
VR6 engine

Fig. 178. An arrangement of an oil radiator on lateral face of the block of cylinders of the VR6 engine: 1 — a directing tube щупа for check of level of oil; 2 — an O-shaped sealing ring; 3 — a cover, 25 N · m; 4 — an oil radiator; 5 — an O-shaped sealing ring





On the VR6 engine the oil radiator of liquid cooling is established on lateral face of the block of cylinders (fig. 178) .
At liquid cooling the oil radiator consists in the case through which there passes working liquid of system of cooling of the engine, and decrease in temperature of engine oil is carried out by cooling liquid. Hoses for a supply and removal of cooling liquid approach to accession places on the filter.
To remove the oil filter it is possible after cooling liquid from system of cooling will be merged and hoses of a supply of cooling liquid are disconnected. Then unscrew a cover from outer side of the oil filter and remove a radiator. On each party of an oil radiator there is an O-shaped sealing ring which should be changed always if the oil radiator was removed.
The oil radiator with liquid cooling provides not only oil cooling at work under trying conditions, but also fast warming up of oil at engine start-up.
At installation of an oil radiator grease both sealing rings with engine oil. Establish a radiator and tighten a cover the moment of 25 N · m. Attach hoses and fill in cooling liquid in cooling system.