VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
+ 2. VR6 engine
+ 3. Two-liter engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
- 13. Forward suspension bracket
   13.1. Removal and installation
   - 13.2. Repair of a forward suspension bracket
      13.2.1. Screw spring and shock-absorber
      13.2.2. Replacement of bearings of wheels
      13.2.3. Removal and installation of cross-section levers
   13.3. Stabilizer of cross-section stability
   + 13.4. Adjustment of corners of installation of forward wheels
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema








Repair Sharan/Sharan Volkswagen>> Forward suspension bracket>> Repair of a forward suspension bracket>> Replacement of bearings of wheels
If you remove the wheel bearing, it will collapse. Therefore it is impossible выпрессовывать the wheel bearing for check of its condition.
To remove the case of the bearing of a wheel, see item 13.1. After removal of the case of the bearing turn on or the bolts fastening a spherical support, or disconnect it. Remove an amortizatorny rack from a rotary fist;
- after removal of the case of the bearing of a wheel make adjustment of corners of installation of forward wheels.
Replacement procedure of the bearing of a wheel:
- remove a disk of the brake mechanism (bolt) and a reflector of a rotary fist (3 bolts);
- put a rotary fist with a wheel nave the forward party down on a press and squeeze out a wheel nave by means of a press opravka via the wheel bearing. The way of installation of an opravka is shown in drawing 289 . The effort can be applied only to a reverse side of a nave of a wheel;
- carefully clear inside of an opening of the bearing and take a lock ring of the bearing of a wheel (nippers for removal of lock rings);

Fig. 289. Vypressovyvaniye of a wheel nave from a rotary fist. The press plate 2 which should press only on a wheel nave is put on a punch of a press 1. The wheel nave at expression falls in the substituted piece of a pipe 3. At expression of the bearing replace a press plate 2 with another which will press only on an external holder of the bearing





- in position of a rotary fist on the press (see fig. 289 ) squeeze out the wheel bearing outside. Use for this purpose an opravka which has the size corresponding to an external ring of the bearing of a wheel;

Fig. 290. VW431 stripper for removal of an internal ring of the bearing of a wheel





- squeeze out an internal ring of the bearing of a wheel by means of a dvukhzakhvatny stripper (fig. 290) ;
- carefully clear a rotary fist. A reception opening of a rotary fist cover with graphitic Molykote greasing.
Assembly order:
- put the case of the bearing of a wheel on a press (see fig. 289 ), впрессуйте the bearing and establish a lock ring;
- put a nave on a press and впрессуйте the case of the bearing of a wheel with the bearing established in it in a nave. Use for this purpose the pipe piece which diameter corresponds to internal diameter of the bearing, that напрессовать the case of the bearing of a wheel and the wheel bearing against the stop on a wheel nave;
- other works carry out in return sequence concerning removal process.