VW Sharan repair

. Diesel engines: 1,9 l of TDI.
+ 1. Introduction
+ 2. VR6 engine
- 3. Two-liter engine (ADY)
   3.1. Removal and installation
   + 3.2. Dismantling and assembly
   + 3.3. Head of the block of cylinders and valves
   + 3.4. Pistons and rods
   3.5. Block of cylinders
   + 3.6. Cranked shaft and radical bearings
   + 3.7. Drive of the mechanism of a gazoraspredeleniye
   3.8. Adjustment of a tension of a driving belt of units of the engine
   3.9. Intermediate shaft
   3.10. Compression check in engine cylinders
   3.11. System of production of the fulfilled gases
   3.12. Cleaning system with absorbent carbon application
   3.13. System of a retsirkulyatsiya of the fulfilled gases
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
+ 13. Forward suspension bracket
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema




Repair Sharan/Sharan Volkswagen>> Two-liter engine (ADY)>> Adjustment of a tension of a driving belt of units of the engine
The tension of a poliklinovy belt is carried out by the mechanism with the built-in spring and does not demand regular control. Therefore it is not required to carry out special adjustment of a tension of a belt if it for any reason was removed.
In spite of the fact that various units can be established and for their reduction in action various pulleys can be used, only one tension roller is in any case used.

Fig. 156. The scheme of laying of a poliklinovy belt on the car without the conditioner. To weaken a belt tension, turn the lever established on a tension roller in the direction, shown by an arrow




Fig. 157. The scheme of laying of a poliklinovy belt on the car with the conditioner. To weaken a belt tension, turn the lever established on a tension roller in the direction, shown by an arrow




Schemes of laying of a poliklinovy belt on the car without the conditioner and with the conditioner are presented on (fig. 156) and (fig. 157) respectively.
Removal of a poliklinovy belt is carried out as follows:
- mark the direction of movement of a poliklinovy belt. For what draw with a marker an arrow in the movement direction. The cranked shaft of the engine rotates clockwise if to take a detached view a belt;
- the lever 3299 (see fig. 156 and 157 ) weaken a tension of a poliklinovy belt;
- remove poliklinovy a belt from the driving mechanism of the pump of the hydraulic booster of a steering;
- remove poliklinovy a belt;
- check a condition of a poliklinovy belt. It should not have cracks or breaks, otsloyeniye of a covering or fibers, shabby fibers, обтрепавшихся or steklovidny lateral surfaces, oil or fat spots;
- damaged poliklinovy it is necessary to replace a belt surely.
Installation of a poliklinovy belt is carried out as follows:
- turn the lever 3299 a tension roller and put on poliklinovy a belt a tension roller and the generator (if the belt is established old poliklinovy, observe the direction of movement specified on it);
- release the lever 3299 a tension roller that poliklinovy the belt stretched.