VW Sharan repair

. Diesel engines: 1,9 l of TDI.
- 1. Introduction
   1.1. New VW Sharan
   1.2. Car identification
   1.3. General recommendations about car repairs
   1.4. Conditions of work and the used tool
   1.5. Correct lifting of the car
   + 1.6. Works on repair and service
   1.7. Lubricants, hermetics, Loctite
   1.8. Corrected addresses with carving connections, bolts, nuts
+ 2. VR6 engine
+ 3. Two-liter engine (ADY)
+ 4. System of greasing of the engine
+ 5. Cooling system
+ 6. System of injection of fuel of the VR6 engine
+ 7. Simos system of injection of fuel of the 2,0-liter engine
+ 8. Ignition system
+ 9. Coupling
+ 10. Mechanical 5-step transmission
+ 11. Shaft of a drive of wheels
+ 12. Hydraulic booster of a steering
+ 13. Forward suspension bracket
+ 14. Back suspension bracket
+ 15. Brake system
+ 16. Electric equipment
+ 17. Diesel engine
+ 18. System of greasing of the diesel engine
+ 19. System of cooling of the diesel engine
+ 20. Power supply system of the diesel engine and turbokompressor
+ maintenance Card
+ Specifications and characteristics
+ Elektroskhema

Repair Sharan/Sharan Volkswagen>> Introduction>> Car identification
The factory plate is on the right average rack under the door lock. Number of the chassis which has been beaten out on a partition of a motor compartment, except the current production issue displays type, year of release of the made room model and its production. It is put also on a sheeting of a control panel about a windscreen that he could be read easily outside. The factory plate informs on the name of firm manufacturer and its symbol, registration number, identification number (VIN) of the chassis of the car, allowable full weight, allowable full weight with the trailer, a permissible load on a forward axis, a permissible load on a back axis.
Identification number (VIN) of the chassis of the car, beaten out on a body, on EEC standards 17-unit and except serial number of the car displays code number of model, year of release and a place of its production, the international designation of manufacturing firm.

Fig. 1. An arrangement of identification number on the VR6 engine

At the 2,8-liter VR6 engine serial number and code designation of the engine (AAA) are beaten out on a forward part of the block of cylinders (fig. 1) .
Besides code designation (AAA) of the VR6 engine is given also on the factory plate with designation of model of the car, and on a cover of a head of the block of cylinders there is a sticker with the indication of serial number of the engine.

Fig. 2. An arrangement of identification number on the 2,0-liter engine (it is shown by an arrow)

At the 2-liter engine code designation of the ADY engine and serial number are beaten out on the left side of the block of cylinders (fig. 2) .
Serial number of the engine is located on a protective cover of a gear driving belt. Code designation (ADY) such as the engine is given and in the factory plate with designation of model of the car.

Fig. 3. An arrangement of code designation on a transmission: the arrow 1 showed a place where code number is located; an arrow 2 — a place where the transmission type is designated

The transmission too has code number. Its location on a transmission is specified by an arrow 1 (fig. 3) , it designates transmission type. In a place specified by an arrow 2, it is reported, about what transmission there is a speech.
On one side transmissions its code number which is specified also on the factory plate is beaten also out.
At the order of spare parts it is necessary to specify the exact name of model and chassis number, and also whenever possible number of the engine and year of release. It considerably will accelerate obtaining the order and will allow to avoid mistakes in it. Only at the indication of mentioned numbers the supplier of spare parts can sell the spare parts corresponding to the concrete Sharan or Galaxy model.