VW Sharan repair. Diesel engines: 1,9 l of TDI.+ 1. Introduction + 2. VR6 engine - 3. Two-liter engine (ADY) 3.1. Removal and installation + 3.2. Dismantling and assembly + 3.3. Head of the block of cylinders and valves + 3.4. Pistons and rods 3.5. Block of cylinders + 3.6. Cranked shaft and radical bearings - 3.7. Drive of the mechanism of a gazoraspredeleniye 3.7.1. Removal of a gear driving belt 3.7.2. Installation of a gear driving belt 3.7.3. Ignition installation 3.8. Adjustment of a tension of a driving belt of units of the engine 3.9. Intermediate shaft 3.10. Compression check in engine cylinders 3.11. System of production of the fulfilled gases 3.12. Cleaning system with absorbent carbon application 3.13. System of a retsirkulyatsiya of the fulfilled gases + 4. System of greasing of the engine + 5. Cooling system + 6. System of injection of fuel of the VR6 engine + 7. Simos system of injection of fuel of the 2,0-liter engine + 8. Ignition system + 9. Coupling + 10. Mechanical 5-step transmission + 11. Shaft of a drive of wheels + 12. Hydraulic booster of a steering + 13. Forward suspension bracket + 14. Back suspension bracket + 15. Brake system + 16. Electric equipment + 17. Diesel engine + 18. System of greasing of the diesel engine + 19. System of cooling of the diesel engine + 20. Power supply system of the diesel engine and turbokompressor + maintenance Card + Specifications and characteristics + Elektroskhema |
Repair Sharan/Sharan Volkswagen>> Two-liter engine (ADY)>> Drive of the mechanism of a gazoraspredeleniye>> Ignition installation Installation of ignition is necessary for the correct connection of the distributor with a drive from the engine and with spark plugs in order that the spark in cylinders of the engine moved during the necessary moments. Installation of ignition is carried out before putting on of a gear belt, and also in case of its wrong installation or slipping of a gear belt (the belt jumped through tooth).
Installation of ignition carry out in the following order:
- turn out spark plugs;
- put on a gear belt cogwheels of a camshaft, a cranked shaft and an intermediate shaft (the provision of cogwheels yet does not play any role);
- temporarily establish a pulley of a cranked shaft on a cogwheel of a cranked shaft (a protective cover it is not necessary to establish), thus pay attention to coincidence of labels on a pulley and a cogwheel;
- turn the engine (by means of a key of the cogwheel of a cranked shaft dressed on a bolt), the corresponding labels will not coincide yet. Thus it is necessary to pay attention to the next two moments:
- if the engine is established on the car, it should be turned until a label 1
(fig. 152)
on a flywheel (for a mechanical transmission) or a label 2 on a driving pulley (for an automatic transmission) will not appear in situation (see
fig. 152
);
- if the engine is removed from the car, turn a cranked shaft of the engine until the flute on a quencher of fluctuations will not be established in situation shown on
fig. 153
;
- adjust the provision of an intermediate shaft (at even loose gear belt), for what:
- uncover the ignition distributor to see the provision of a rotor;
- turn a cogwheel of an intermediate shaft in the direction shown by shooters
(fig. 154)
so that the rotor of the distributor of ignition occupied situation shown on
fig. 155
.
- put on a gear belt. Now the first cylinder of the engine is in the provision VMT of the end of a step of compression and in the ignition moment;
- check, whether labels on a camshaft gear wheel (see
fig. 127
) coincided;
- again remove a pulley of a cranked shaft;
- pull a gear belt (see item 3.7.2).
|
|